Search results

Thanks for the input everybody. Went with a piece of black starboard.

I'm replacing my old Furuno radar with a Simrad Halo 20+. Since I will no longer need the Furuno MFD, I'm replacing it with a Simrad NSX 7" that will fit flush in the dash in its place. Problem is, the Furuno's going to leave a bigger hole than the NSX 7 is going to fill. First thought is...

https://www.classicparker.com/threads/bow-roller-upgrade.14266/#post-97474

Night mode

The EVO3S has 2 card slots so I'm running both. I'm still getting familiar with everything each chart can do. My early impression is the CMAP Reveal bottom floor view looks nice but doesn't have as detailed bathymetric lines as the Navionics Platinum. The Navionics lets me do live downscan...

I have a 2008 2120 with F225 on the back with a very similar gelcoat crack. As far as I've been able to tell, the transom is solid and no structural issues going on. I scraped the gelcoat along the crack to widen it and filled it with epoxy. Plan is to cover it over with a fresh layer of...

My Furuno 1724C and DFF1 fishfinder were nearing 15yrs old and the DFF1 gave out on me. No signal to the transducer. There weren't any great options for just replacing the DFF module so it was time to finally upgrade. I installed this new Simrad 9" EVO3s and a StructureScan 3D module. Until...

great video, subscribed!

To clean your plexiglass without damaging, Plexus plastic cleaner is really great stuff. I use it on all my plexi windows and hatches. Not affiliated except as a satisfied customer... http://www.plexusplasticcleaner.com/boat.html

Those 2mi Attwood LED navlights are what I use too. The green died on me in the 2nd year. Installed another of same model going 3years now on the green/stb replacement and 5years for original red/port with no other issues. They have a 10yr warranty so you shouldn't normally have any issues at...

2014 Grand Cherokee SRT 470hp 6.4l hemi, 8 speed tranny, 0-60 in 4.6 sec., made in USA and can tow stuff (7200lbs). Fit the Parker trailer coupler perfectly :D

After sea trial, I ended up adding 1/4" shims fab'd from 1/4" starboard into shape of the actuator mounting footprint and mounted using 1/4" longer bolts. The Lenco recommendation is trailing edge of tab should be 3/4" above the plane along the bottom of hull. Using the Parker factory...

My 2120 SC has a F225 too and I raised the motor twice, finally ending up at the highest bolt hole position. What prop do you have? I'm spinning a Yamaha SWS II 15.75 x 15pitch and can just touch 40Mph@5900RPM. You can see in the picture I also added a Bob's Machine Shop wedge to give a little...

Got mine online from BOE Marine for $739 (Lenco 12x18 edge mount kit w/ LED switch) Wanted to do the LED switch upgrade while I was at it and trying to buy only the tab blades while also wanting a new LED switch separately didn't make much cost sense over just getting a new full kit. The...

The tabs are 1/8" SS and don't appear to flex much so I think it'll be ok as is. If I find out otherwise, I'll probably do something like you describe to both bolster the offset area and provide a small amount of shim to adjust the tab range downward a bit (not with alum. tho). I don't think...

My original Parker chair slider never stayed locked in place either. I replaced mine with a Todd slider along with new helm chair. http://www.classicparker.com/phpBB3/viewtopic.php?f=8&t=12570 It's a standard bolt pattern if you want to just replace your slider and any of the common aftermarket...

Here's the result after changing out the factory 12x12 Lenco tabs for 12x18's Full up position, reads 2degress from level - the boat is sitting bow high with trailer tongue jack raised full down reads ~18 degreees, so I have a little over 15degrees total travel. trailing edge is 7/8" above...

New Yamaha offshore F225 4.2L "big bore" V6 :) http://www.yamahaoutboards.com/outboard ... ifications

Just after having 1000hrs service done on my F225 I noticed an oil leak. Oil was leaking from oil pump seal going down the shaft and dripping out the foot of the lower unit. Apparently another problem being seen on these Yamaha's at around 800-1000 hours mark is a groove getting warn between...