Search results

Parker 2520 I have a leaky deck/hatch/window on it. The window I'm talking about is the overhead window/hatch in the cabin underneath. I'm not sure where exactly its leaking from. I siliconed it pretty good hoping that's the issue but its still leaking. Is this something that happens often...

I'm in the process of swapping out my old Lowrance FF/Plotter for a Hummingbird. I have a Lowrance fuel flow sensor installed on my old system. Can I use my Lowrance fuel flow sensor on my new Hummingbird system? Or do I need a sensor specifically made by Hummingbird?

Parker 2520 I purchased a gps trolling motor to install during the off season. I have seen a few mounting ideas but my question is this. Has anyone ever mounted a TM on the pulpit. I was thinking about removing the anchor and storing it in the cabin. (I rarely use the anchor anyway). I'll...

I'm in the market for a trolling motor for my 2520. My primary plotter is the Garmin 94sv . I also use Lorance HDS7 as my back up. any recommendations? An guidance would be appreciated Thank you

1995 2520...2003 Honda 225....I'm having fuel starvation issues. It high rpm the ball collapses and the motor boggs down. I replaced all the lines from the motor to the tank. I switched from 1 existing pickup to the other existing pickup. Same result. I'm sure it's possible that both pickups...

I'm looking for the teak step gunnel plates for my 1995 2520.

I have a seastart steering system. I just replaced a hydraulic hose from front helm to rear helm . filled and purged (i think) now i can only turn the motor to one side then it locks up. I would have to open the bleeder and manually turn the motor to get it back. Then it would do the same...

1995 2520. Just from age and wear and tear there are a few spots where my carpet in the cabin has lost its adhesion. Without tearing it all down what's my best method to get it to adhere back up?

I'm in the market for a new steering hose . The problem is the hose is "hynautic 5/16 ID 90-5291" I CAN'T FIND A REPLACEMENT ANYWHERE. Is there anyone that can help me?

1995 parker 2520 that is in need of a topside cleaning and waxing. whats the proper procedure to do so? and whats the best cleaners and waxes to get the job done?

1995 2520. What are you guys using to wash and wax topside? Top of my pilot house is a little chalky. My deck isnt chalky but can use a good detail. What's recommended?

1995 2520.. I have a Crack on the top of my transom in a weird spot. It runs along the very top horizontal edge. I had a friend who has pretty good boating knowledge look at it and he says it's no big deal. Grind it and epoxy it. It will be fine. Others tell me it's a BIG issue. What do...

Ok 2003 honda bf225. Motor trimmed up on its own and wouldn't go down. Had to manually lower it. I did a ton of troubleshooting and came up with this. The trim motor works up and down when I bypass everything. The relays are clicking . Bottom line is I'm getting power to the blue wire...

I'm looking to put a display by my rear console. I don't need to have any control over it. Is there a way I can put a monitor there to display what's on my main screen?

Is it possible to fill the system with fluid from just the helm in the cabin? I installed a bulkhead station but did not install the remote fill so right now I cannot access the fill on that helm. Can I fill the whole system from one helm?

My overhead window on my 2520 leaks in heavy rain and spray. Best way to fix this? Front windshield that pivots open leaks too.

I'm installing a rear bulkhead station on my 2520. What size steering wheel do you guys recommend ?

I'm looking for some rod storage idea in the cabin of my 2520. And ideas?

Heres my problem. I drilled the hole I epoxies the fiberglass backer plate. I put the through hull in and tightened it to set the epoxy. Now here's where I get messed up. I was planning on removing the pick up and cutting it to the correct length. (Something I should have done before I...

With a dual station hydraulic steering system. Do you have to fill both helms seperately or can you fill 1 helm and work the fluid through the entire system?