Search results

just repowered my 2510MV with Armstrong bracket with Suzuki 300. Dealer installed the engine all the way down - the same as the previous Yami. im Afraid that’s a tad low. For those with similar setups what hole did your Suzuki get mounted?

I'm repowering my 2003 2510 with a 2023 300Hp Suzuki and would like to upgrade the steering cylinder to a UFLEX. The UFLEX website is pretty confusing. I think I need the type 2 in either a UC128 SVS or UC128-TS. The type 2 has the bent link arm vs the straight link arm of the type 1. Can anyone...

For those that repowered did you go with the white or black. I was set on the white but dealer started steering me to black. What's everyone thoughts?

Has anyone installed a jackplate on their Armstrong bracket? I'd like to keep as many motor options open as possible, and if a 30" becomes available, I'm wondering how possible the install would be on the bracket.

The opportunity has presented itself to repower with a new Yamaha F300 for essentially the same money as the Suzuki 300 that I'm currently on a wait list for. I'm scared of the Yamaha corrosion issues you still see rearing their ugly heads on motors produces as recently as 2018. The boat is kept...

I have a Fusion RA70 installed along with 2 speakers mounted beneath the hardtop facing the cockpit. I'd like to install 2 more speakers. Has anyone installed speakers into the sides of the electronics box mounted beneath the hardtop?

When removing the enclosure, a couple of the female portion of the snaps pulled from the windshield. Yes, I should have taken more time when removing it, but I didn't have any! This half of the snap is still attached to the curtains. Is there a procedure to replace the half attached to the...

Wondering if anyone has repowered with a 350hp outboard - Suzuki or other. One has become available, however I'm not sure if I should wait for the 300hp.

After reading many other informative posts, I’d figure I’d share my install. I can’t yet vouch for the functionality of it yet, but so far it looks good. I opted to mount port side utlizing a shuttle slide mount. Note that I have it mounted on a custom plate I made that hasn’t been tested by...

I've taken on the fun task of removing what could be 20 years of bottom paint! The bottom wasn't terrible, but paint was thick, peeling in places, chipped in places, and generally rough. This is my first season with the boat so I'm trying do it right. I'm going at it with a chisel and sander...

Is Replacing the stock 1-2-both switch to the BEP cluster as easy as switching the wire from the "1" position to the "start" on the BEP and "2" position to the house on the BEP? I have the BEP cluster but don't want to disconfigure a working system and screw things up.

Are these factory connections??? Anyone know what accessories are grounded here? This bus is located on starboard side of bilge. Shouldn't this bus be grounded directly to meg at battery as well?

I've been searching previous post on various TM installations. I'm wondering if anyone has mounted a Rhodan 84" on a 2520 or 2510 without cutting the bow rail. Most of the installs I see where the rail isn't cut are with the minnkotas. I'm wondering if the Rhodan could be lowered similarity...

2003 2510 or similar. Anyone successfull or have pics of a cutout tackle system installed in the box beneath the pedestal seats?

For those that installed rod holders in the transom, what angle did you use? Is there enough space to fit a 30 degree, or do you have to go 15-degree. I'm looking to add two to either side of the transom fish box. Thanks!

Any update from those that installed the T-H marine 6" twist off plates. How are they holding up? I see Great Lake skipper has the temptress Parker 6" twist off plates. Trying to decide between the two. Thanks!

I'm assessing the plumbing and thru hulls on my new to me 2003 2510. I currently have a Rule 1500 aft and a Rule 360 forward bilge pumps. Both are on float switches and seem to function as they should. Is this a factory setup? The 1500 seems to be plumbed with 1 1/8" and the 360 with 3/4" hose...

What does everyone use to squeeze an extra rod holder or two between the factory 6 welded on the hardtop. Is there a clamp on version that extends out enough to create an offset? Thanks!

I bought the above boat with original F225 Yamaha. I'm learning the tabs and trim getting the bow down in chop. I've only been on the boat twice, both in choppy conditions. Even with boat trimmed all the way down I've cavitated it twice at cruise speed cutting through the waves. I was afraid I...

What do you guys use for cabin rod holders. I'm thinking something overhead. Not much storage space on for anything on these Parkers!