Splash well guard for a 2320 sport cabin. Notched transom.

[Spdnby]

Hello looking to buy the Parker version of a splashwell guard for a 2320 sport cabin transom.
The opening is 39 1/2" wide.

I could make one but would like the factory instead.
It will be easier.

 

[Brent]

Wow that is a lot of water. When this occut? Contact Parker directly or a dealer. Cecil Marine has a web site it that sells Parker and might be able to order it too

 

[Spdnby]

Hi Brent,

Thanks for the concern. It is a lot of water......
I called Parker who said I needed to go to an authorized dealer.
I did that too.
Dealer told me that it took a week for Parker to answer the dealers email cause they tried looking at any dealer who would have some new old stock.
The dealer called me and said Parker found none, and that they no longer have the mold.
Regardless I'm calling Parker myself tomorrow again as I have a couple of questions for them.
If I get nowhere I'll be making one out of starboard. Fairly simple.
Boat outfitters has the starboard I need for about $65 bucks.
BTW....could anyone measure the thickness of the Parker piece? I priced it at the 1/2 " piece.

Thanks.

 

[Shannonigans]

. . ..the factory splash well is just fiberglass. ...maybe 1/8" thick. I will be fishing tomorrow, so I will try to remember to get a measurement for ya. The splash well will definitely keep all that water off the deck!! My well fills, but deck stays completely dry. .. ...If you don't get anywhere in getting the one from Parker I can check the dealer by me. ..Boat's Inc. ....doubtful but I can still ask if you want.

. . ...also. ..it's hard to tell from the pic but I am assuming you have two 6" deck hatches right in front of the motor. . ...which are in a larger removable rectangular piece?? Make sure that is sealed up good. .....when I bought my boat the guy had it removed and I just wanted to dunk her. ....so I didn't seal it properly before putting her in .....and all that water fills the bilge pretty quick. No need having your bilge pump run that much!

 

[Brent]

I would call Eric at Parker corporate and order it. m2cw

 

[Brent]

I hope your bilge pump is new and have a second one.. Your pic is scary

I would pull all deck plates and check them
m2cw

 

[Spdnby]

Hello there....it is pretty scary.....
Deck plates were pulled and pump is in good working order.
I also did reseal the rectangular piece that both circular access plates are mounted on.

Hopefully today I can get a call out to Parker. I'll ask for Eric.....


Thank you.

 

[qsweet]

Hello there....it is pretty scary.....
Deck plates were pulled and pump is in good working order.
I also did reseal the rectangular piece that both circular access plates are mounted on.

Hopefully today I can get a call out to Parker. I'll ask for Eric.....


Thank you.

Hey just wondering how this worked out for you? I am having the same issue and would like to get one of these splash guards. Thanks

 

[PKS1801]

I know this is an old thread, but what I did to assure that I did not lose a pie plate at the wrong time, ie, washed overboard, was to drill a tiny hole through one of the ribs on the bottom, and attach each to something below deck with 100lb mono.

 

[SOUTHWINS]

i have a 2120 but this is what did works great

 

[Inshore Chaser]

i have a 2120 but this is what did works great

Looks good! I noticed you mounted it on the small thinner lip of the transom. Is that lip 100% fiberglass or is there a wood core? Thanks

 

[SOUTHWINS]

can you pm me inshore chaser

 

[Mtbmiller]

I have one that came off my 2120 if you want it. 2006

 

[Inshore Chaser]

can you pm me inshore chaser

Sent a pm