Search results

I used to run out on a regular basis when I was living down beach. Not as much anymore, will be relocating boat to new location in Maine. But we would go out of Indian River Delaware to fish between the canyons from Massey’s to Baltimore (4 stroke), ranging 35 - 70 miles one way. However, I also...

Thanks I bought a straight and curved set of needle nose pliers that are 12”. Found them in tractor supply on the discount rack. I will try them this weekend. Thanks.

I have a Yamaha 250 4 stroke and when I started it I noticed water coming out from under the motor cover. I traced it back to a hose that popped off. It is located on the port side of the engin and the water is running through the engine and this hose seems to feed the tell tale discharge. The...

I have a 2310 and purchased a Load Rite trailer in 2009 for $3438.00 since then I have used it approximately 30 times for hauling in and out seasonally to my slip, for removal during potential hurricanes, some maintenance and the occasional trip to the Chesapeake. The boat is a heavy one when...

That is unbelievable. If you are going to replace them, consider making the the back two swivel holders. They come in handy if your ever offshore and into any big fellows.

I just came across your job and photos. It is an awesome job and great use /improvement of that space. You are correct, I have to clean out my box several time each season due to the build up of rain and washdown water. I wish I had someone out here that could do that for me. Great job!

Guys, I am back and sorry but haven't been around in a while. This was always a great site for me and I always enjoyed it. In Sept of 2015 my Yamaha F250 had a major failure with only 120 hours on it. The factory Rep came to the dealer to inspect and they were unable to identify the cause of the...

@ Sam3, I have a 2310 with a platform and purchased a new Yamaha 250 two years ago to replace my 225. It was installed by a non-Parker dealer using the top hole on the mount and the top hole on the engine. However, the 250 engine is a bit heaver then the 225 and It just seems to be slower out...

Mike, Sorry I have not been here for a while and missed your post. I had one in my shed collecting dust and adapted it to a small 14' crab boat for the back bay. sorry.

Ray, If you are referring to the water inlet covers that are plastic, I remove them once or twice a year and make sure they are clean and clear. I have never painted the inside of it. It is still the original blue and after a few years in the water, I only had one little growth on the inside...

Ray, While you have her high and dry, you may want to consider purchasing paint for the lower unit and paint it as well. The 2310 is very heavy in the stern and as a result when I have a full tank of gas (150 gallons) the bottom of my engine is still in the water. So I paint the bottom of the...

Ray, Sorry for the delay. I have been working on my boat all weekend and got out this afternoon for a few hours. Her are the photos with measurements for you to determine if you can cut a hatch. Walt

Will do. I am heading down to the boat this evening. I will get you all the detail tonight or tomorrow. I am installing a new 30Amp panel hopefully this weekend.

Yes I am wired to the switch panel with a spring loaded toggle. It is always on, even when the main power os turned off. The toggle allows for remote activation without the float switch.

My boat was built in November 1999. I purchased it in June 2009 from the original owner and replaced the engine with brand new Yamaha 250 in July 2011. I just searched my old photos and did find some original photos of the bilge pump when I first bought it. The location is under the interior...

I have a 2310 and my forward bilge pump in located at the bottom of an access hatch that is located on the inside steep of the v-birth. It has a discharge line that goes up and through the starboard storage compartment and thru the hull in the middle between the starboard bow and beam. I am...

Sorry for the delay, but I did manage to complete this project. I could not purchase the product identified locally so I bought Boat Life and used it to reglaze the lens into the frame. Once I did it, I covered it with canvas and let it sit until the following weekend that I was at the boat. It...

Where are you located? I have a black Bimini canvas top that is on the stainless steel frame. I upgraded to a hard t-top.

Thank you very much, going to store now to see who has it. I want to get this glass back in. thanks again!

I have an old Taylor Made hatch above the v-berth of my 2310 that has a bad water leak when it rains. The past few times it rained the water just seemed to come pouring in :( , fortunately my cushions are still inside from winter. I checked and the bedding of the frame seems to be fine and not...