Search results

Have a 2003 if interested

I have a 2003 2510 and am ready for a possible repower as I like to go far out and need the speed. My current 225 is ok but again I only go on calm days so would like the piece of mind of new power with more speed. My Parker has a max HP plate of 325 on the boat. I don't know if I ever seen one...

I am thinking about repowering from a F225 to a F300 on my 2510. Can you give me the name of the company you used for the repower and are you happy with the job. Thanks, Paul

I am thinking about repowering my 2510 from a F225 to a F300. Could you give me the name of the person you used for your repower and are you happy with the job. Thanks

I also have one that works great at 10 mph +speed but you cannot troll at slow speed with it.

I have a problem with the overheat alarm. It only happens at low rpm in a trailing sea. The pisser tube is not flowing hard like it should so I replaced the water pump impeller but it made no difference and the impeller looked fine. I am Thinking that the theromostat might need replacing. What...

I am thinking about purchasing a trailer for my 2510. What model and size should I get?

Thanks for the help and advice. I went in the water yesterday and put the tabs back on using a coathanger for now and added zincs to the tabs. I hope this will last until I either get new tabs or new pins. I really dont want to pay for a haulout in the middle of the season. The old pins has...

no they did not but zincs are close on the motor and bracket

i just purchased a new s1000 and installed it as recogmended . I installed it behind the stearing station on my 2510 inside the fiberglass electrical box. The problem is that when I am standing at the rear of the boat 8 feet away the system looses signal from the remote and it goes into...

I up graded my trim tabs with 12X18 blades on my 2510 and the other day I noticed that the port blade was dangleing. After further inspection I found that the hinge pin was gone. There was a rust stain at the hinge. Did the pin rust away, the tabs are less than 6 months old. Did Lenco not use...

Fish Pimp, How much did you spend on the components? I was thinking about one but not sure if I can afford it yet.

I found some water inside one of my tabs and want to replace the motor before spring dump. does anyone know of where I can purchase just the motor. Lenco only wants to sell me the whole new actuator. Thanks, paul

I came up the bay the other day in 17 to 25 knot winds. The boat took a beating and so did I but the boat took it and got me home. I think the boat can handle more than me.

I ended up taking the sending unit apart and found debris that was very small. I cleaned it up and put it back together and it works fine. I ran the boat to Norfolk and was amaized at the difference in mpg due to sea conditions. The best I could get was 2.4 mpg at 4800 rpm. The worst was around...

Just installed a new Yamaha fuel management sysytem on my 2510 with a single 225. I went with the yamaha system because it matched the other guages and I firured it would be easier to install and interface, but Im having some issues and could use some help. I hooked all the wires comming from...

I need some advice on props. I have looked at a lot of info on this forum but have seen very little on my particular boat. It is a 2510 MV with a 225 yamaha on a armstrong bracket with a black factory prop marked 17 M. The tabs are factory tabs. The boat runs fine but it seems a little slow. I...

You really need to go test drive in sloppy conditions to get the real value of the ride. The 2510 mod vee is great in smooth water and with a little chop. Two to three footers and you will have a rough ride. Four to five and you have to go about eight knots, but you will get there. It seems...

I am trying to find out if the factory 17 3 blade black prop on my F225 2510 MV is the best prop for the boat. I have read a lot of info on other boats , the 2520 Dv and others but not much on the 2510 MV bracket mount. I am looking for economy first as I usually am underloaded, and like to go...

This is my first oil change since purchase last year on a 225 4stroke on a 2510 2003. What type and weight oil should I use. I did not get a motor manual with the boat. Also how about the gear lube? Anything else?