Search results

plugs all replaced

Bulbs not replaced, it’s on the list to try. They are mostly vertical. Never considered the hull vent. Tried portable tank. However, that was before replacing most of the engine pumps an filters. Haven’t tried it since. No idea is a bad one at this point. Thanks.

2004 Yamaha 225 4s. Won’t throttle past 4 k. Changed all filters from external water separator to injector filters. Changed VST and pickup pumps. Idle is fine and throttle is good up to about 3800. Tank has been run near dry and fresh fuel. Been happening for several months intermittently. Boat...

I got the key code off the fixture and ordered replacements on eBay for pretty cheap

Search on eBay. Stainless gas shocks. The vendor is strut-your-stuff-here. I just bought some from him a couple weeks ago. About 25.00 each. Has a good selection and good service.

Easiest way may be to remove actuator and splice a thin, stiff wire to the end of existing cable. Then, stuff as much of it in from the outside until you can see/find it Inside the boat. I have done this with many different wiring situations. With my 2820, all of the wiring runs up from the...

Would a high quality paint work well after smoothing surface?

bump

I run a 28 Parker w twin 225s. Most of my fishing is offshore in the atlantic off the OBX. Every trip is different. There is no, right for all conditions, trim and tab configuration. On an average 40 mile run, I am usually at about 36-3800 RPM and 24-27 MPH. Some conditions dictate 16-18 MPH. It...

I use seafoam. 15 year old 225s. Just had compression test and was at 140 at each cylinder. I’m not sure if that is a great number, but it is consistent across all cylinders. For 250 gallons it is not much cheaper than ring free though. I use about 2 gallons of saefoam at a time Benefit for me...

if anyone is having problems with their power trek/marinetek shift and throttle control system, I have the parts from my old one. The system is complete. Could possibly be missing a wire or so, but i think I got them all. We are pretty sure that the only faulty part of the system is the...

They have an aluminum frame

finally Fixed the shift issue. my upper station shift was bad. Unfortunately, the shift system, as many here are aware, is no longer made or supported. I had to dish out a ton of cash for the SeaStar i7700 shift system. Hope to have it in the water next weekend. While on the trailer, it seems...

Anyone have any parts for the tek-marine multiple helm station controller system. I’m pretty sure the potentiometers that mount to the bottom of my 704 Yamaha controls levers have gone bad.

How hard are the windows to remove?

Thanks for the ideas. Sure hope I don’t need those cables replaced. They are a beast to run. It was hard just to get power cables for electronics up there. As far as the windows, the pitting is bad. No doubt to early neglect. Trying to think of a good way to coat and color them. Will good...

I’ve been out of commission for a while. I’m looking at getting my boat back up to standard. One issue I have is pretty severe salt pitting on my window frames. I was thinking of priming and painting them. Any better ideas. If not what type of material should I use. I can’t really afford to...

Changed switch, verified connections, bypassed kill switch. Upper station seems all good. Is there something at the main helm that could be the problem. Starboard engine works fine at both stations.

Warthog, Is Parker's decking sufficient to not have an oversized backing below the deck? I am assuming that the ring you mention is approximately the same size as the deck mounting plate. The pedestal base is about 11". I was considering putting it about 12" forward of my bilge hatch and using...

Hello folks. I had not logged in for a long time. Could not get my account name and email to match for login, so I reregistered. My old username was matt5514, just swapped around to 5514matt. Creative huh? Been pretty inactive with the boat in general for a couple years and trying to get back...