My '95 2530

Classic Parker Boat Forum

Help Support Classic Parker Boat Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
What hole is your motor mounted in? Usually a boat will respond well to the motor being raised. The dealer /Factory usually don't really care.

100_4026.jpg


100_4027.jpg
 
Gotta take a photo of mine to be sure, but I think mine is where yours is.
I'll verify that today.
 
OK We got Lucky. The torch on the housing freed the bolts I had broken 1, but after the T&T motor came off there was a nub about 3/16 to 1/4in long sticking up. I heated the housing all around it and it came right out with vise grips.

The system was full of watered down oil. Drained it, cleaned what we could with Brakeclean and blew it out with compressed air.

Took a few hours but with attending to 4 granddaughters 2,3,8 &9yrs old it was a handful. Still it was a relief to come apart and not have to do any drilling and tapping.

100_4029.jpg


100_4028.jpg
 
Finished bleeding the system today and had to pickup a metric bolt that broke.

1st time ever using this lil camera as a movie Vid. :)


 
I thought the same thing.....Then when I tried it at the helm it was backwards too.

What it turned out to be is the internal hook up of the wires in the T/T motor.

So I swapped the Blue wire onto the Green terminal and the Green wire onto the Blue terminal and they function correctly now.
 
Changed out the battery trays. TH Marine OUT...Attwoods IN. These are the trays I use in everything now and have for some years.

There is no corrosion issue.....There is no need for a wrench....The threads are extra coarse and easy to use. Once the tie bar and wing bolts are removed you can pull the battery in ANY direction. Something that is needed in some really tight fit boats. They just make life easier. :)

OLD:
100_4055.jpg


New:

100_4056.jpg


1 Gp24 & 1 Gp27

100_4057.jpg


More out with the old.

100_4059.jpg


In with the New.

100_4061.jpg
 
I have a whole box of brand new Blue Seas stuff on my workbench to do the same thing.
Have not gotten around to ripping into it because the old stuff has been flawless so far.
Guess I need to watch your thread for motivation. :)

Why one group 24 and one group 27?
One house and one starting, or was it a space issue?
 
Got the other fuel sending unit today and installed it. Both tanks now showing 1/2 Full. :)

Got the new battery cables all built. I have a Gp34 Optima and a Gp31 Deep cycle just shoved in there right now until my buddy comes down with the new Interstate Gp24 starting and Gp 27 Deep Cycle.

Cables are not tied up yet.

Going to rework the bilge pump wiring with a terminal board in the back. I'll also add a 2000GPH Rule w/ High water alarm.

The terminal board is something I do for ease of testing down the road and ease of replacing a pump or float switch.

You can see it in this pix in my Mako.

TransomCavity004.jpg


Another Mako that I wired.

100_1358.jpg
 
If you open the back of the 2530 like you did in the Mako, you may be able to duplicate that layout.
If not... I know from experience that access to that area will be a bit 'constrained'.

I've spent a lot of time with my head and shoulders stuffed into that area, so I wish you all the luck in the world.
As always, I know you'll do good. :)
 
You just mount the buss bar for easy access Kev. :) IE: Right in the center of one of the hatches.
 
Looks good Bobby!

I used those same battery trays in my current Grady project. Drilled the same holes for drainage that you did. :)
 
I got checked by the CG this year. I didn't have the type VI throw able on board. It was in the garage at home DA! My fault but it did make it sink in. Those type IV throw ables are supposed to be radially available. Problem is they can get in the way. So I went and measured the bulkhead to the STB side of the door. A 20in unit will fit perfect. I ordered a Orange one. Easy for Marine Patrol, CG to see.
I also ordered a special bracket. Not just any bracket, but one that would not let it swing and frail around, yet be radially at hand.

JB1123SketchLG.jpg


JB1123-20LG.jpg


I ordered the 24 X 9 Bennetts w/ the EIC Switch/ monitor from BOE

default.png


Lets see....I ordered 2 - 316 Stainless 1 1/8in 90deg thru hull fittings and a 3/4in straight one for the front bilge pump discharge. I'll be adding a 2nd rear bilge pump [2000GPH] and High water alarm also.

All plastic thru hulls will go in the garbage.
 
warthog5":1msbzulk said:
I ordered the 24 X 9 Bennetts w/ the EIC Switch/ monitor from BOE

default.png


Lets see....I ordered 2 - 316 Stainless 1 1/8in 90deg thru hull fittings and a 3/4in straight one for the front bilge pump discharge. I'll be adding a 2nd rear bilge pump [2000GPH] and High water alarm also.

All plastic thru hulls will go in the garbage.

Now you're talking! :D
 
Anybody know if Lenco makes a switch like that or if I can use that one on lenco Tabs? I like the light indicators on the side.
 
Today I was sanding some of this bottom paint off in preparation for the trim tabs to show up.

I remover the scupper Flapper to get it out of the way. If your boat has some years on it and you haven't inspected this I suggest you do.

The outside lip of the brass tube had separated from the tube. This will induce water into your nice wood transom.

100_4109.jpg


So one of my pet peeves are pockets that hold dirt and water. It holds sand a dirt that you just can't wash easily out of the boat.

100_4111.jpg


So I take a screwdriver and hammer and remove the brass sleeve on the STB side. Yep it was a little damp. I've replaced a bunch of those sleeves. I do it with PVC and epoxy.

Stb side

100_4110.jpg


Port side

100_4115.jpg


But now I'm going to fix both problems. I turned a wooden dowel on my lathe 1 1/4in OD and drove into the scupper holes. I used a 1 1/4in Fostner bit set inside the hole a little for a guide and marked the center on the dowel well. I then used the mini drill press to bore a pilothole thru the middle of the dowel. This set it up to guide the holesaw pilot bit and cut a 1 3/4in hole thru the transom. This is just slightly larger than 1 1/4in PVC pipe. I used sch 20 as it will flow more water than sch40.

Tools used.

100_4119.jpg


The transom is wetted out with resin and then Cabisol is mixed with the resin. The outside of the PVC is sanded with 80gt. The PVC is cut a little shorter than the hole and the epoxy/cabsol mix is filleted in the outside edges. This makes sure it's sealed.

100_4122.jpg


100_4121.jpg


100_4120.jpg
 

Latest posts

Back
Top