Search results

I have 4 sale 1. 2002 Yamaha 15hp 4s elect start $1200 OBO 2. CMC power T/T mod PT-35 new in 2018 $400 OBO 3.Powr-tran Python kicker steering system with remote new in 2018 $400 OBO 4.Garlick Ez motor bracket 71090 $150 OBO The items for sale were removed off of my boat and were all...

How would you do this 2 engines- 2 start- 2 house deep cycle using BEP switches? I now have 2 battery 1 engine hooked to each battery, I want to add 2 battery and dedicate 2 start 2 house.

I am removing a B175 hw which leaves a 3 3/4" hole in the hull, I have the plug that was drilled out at installation. I want to know the best/easy way to repair. 1. should I pin and epoxy it in 2. take it to a boat fiberglass person 3. leave it in and sell with the boat ?????

Where can I get a dash panel made from my template? I know some one on this site has the answer

I am just shouting out about this great place to eat half/half Maryland crab soup you have to try it. The wife and I eat here when we are in the Chessy Bay area

I have a project I am thinking of doing making a twin I/o Catamaran into a twin outboard boat. I would have to remove i/os and cover openings the transom is about 2" thick, I am thinking jackplates for the obs. The outboards would be above the i/o openings has anyone done this on any kind of...

I have a 2011 2320sl with a F225 4s and a 9.8 Yamaha kicker, on a 2011 Venture trailer with maybe 1000mi on it . The motor has 450hrs 0n main 200hrs on kicker I am thinking about selling here is a list of extras. Garmin 7608xsv gt50 tm b175hw thru hull Garmin A/P Lewmar windlass 220' 8...

I am going to cover my deck and cabin I was wondering if carpet or Dri Dek is the way to go. I would like opinions from people that has done either or both.

I want to use my mfd in my house to play with all the menus, I don't want to bring a battery in doors so what are my options. I have a 12v charger with 2-4-6 amp chg rate or should I get a 120v ac to 12 dc converter? My unit says 27 watt at 10vdc 1.8A current draw max2.3 @12v. The converter is...

I want to replace my house battery with a AGM what are good ones?

I have a 2011 2320 f225 4s 17t painted prop from the factory. I am looking at a REV4 but my Yamaha dealer says Tempest, says Rev4 is not a good prop for my Parker? I am also going to install a Perma trim before I do any other up grades, I have stock 12"x12" tabs.I have read Dales post and was...

anyone use after market fuel/oil filters is so which ones ? I have a 2011 Yamaha F225xca 4.2l

I have a 2320 pilot house where is the best place to mount a external antenna. I have a Garmin 7608xsv mounted from roof inside the boat with internal antenna, I have read Garmins install instructions,Garmin says as close to water line and center of boat. I now have a Standard Horizion ext...

What manual for a Yamaha F225xca? I am above average as far as ability so is it Yamaha or aftermarket. I do routine maintance but just like to have a picture once in awhile to look at. thanks Walt

:?: what happened to the 2320 picture thread?

I have a 2320 with 225yahm 4s I raised the motor as high as it will go. I am at 54=5500rpm wot motor trim 1/2 up tabs 1/2 down, I have the black 17t prop just had it redone. I am thinking 15deg prop but no sure which one 2deg should get me to 58=5900rpm Top speed is 35-36mph any suggestions...

I am raising my motor 225 Yahm 4s is there a tork spec for the bolts. My motor is on a 2320 with a bracket :?:

I know this has been discussed but what do you guys/gals use to protect your touch screen?

I have a 2011 2320 with 225 4s mounted on a bracket I leveled the boat and motor the motor is 2 3/4" above the bottom of hull. I am going to raise the motor 1 hole it is on second hole the wot is 5400 Yahama 17t prop, the reason for lifting 1 hole the cavitation plate is below water I said all...

I have a 2320xl 225yahm 17t prop I am only able to get 5400wot. I tested with 1 person 75gal fuel the boat is normal loaded + 9.9 yahm kicker. The sea condition was smooth (less than 1') I know I need to lower pitch what about dia. I am trying to get wot close to mfg recomendation 6000rpm wot i...