Search results

Relocated to the vertical surface. Came out good. Made room for electronics, feels good where he’ll is now.

Doing a rebuild project on my 1992 Parker 25’ sport cabin. Original hydraulic helm is mounted on the diagonal angle. Not really anywhere to flush mount the bigger chart plotter I’m installing. See attached photo of my previous hydraulic helm on diagonal surface. Going to an electric steer by...

Looking for a dash layout picture of a twin engine helmaster full control with joystick, twin engine controls, Yamaha auto pilot and Yamaha digital display in a Parker.. My boat is older and has lots of old stuff that will have to be replaced, holes left exposed etc.. so a new dash is in the...

@warthog5 can you tell us specifically the important things to consider on this install? QUOTE="warthog5, post: 146281, member: 45"] Here on the Gulf Coast [Pensacola] It's a game changer....It's probably one of the things I do most anymore as to installs. I have one here now to do, but...

Considering a spot lock type trolling motor for my 2520, specific motor recommendations wouldnbe apprecotedI like the mount on custom pulpit shown. Question- do I need a dedicated battery bank? I have 4 deep cycle marine batteries (can’t recall group size, but they are large diesel pick up...

thanks for the info, i am in northern california, I will work on getting profile updated. Dale how are the pads from sea del? hard on the knees? hard to clean? those are my 2 concerns? I had factory pads on my boat, they caught water in the winter and rotted, paid a canvas shop to make new...

Do you have an email or phone for him? Thanks for the tip

thanks for the technical terms that will help, your right I didn't get the piping or the rolled and pleated look, and yes I think I got a crappy job from a crappy place, kind of par for the corse in a small community with out much competition. I hear you about the hardness of the seadek, that...

Looking for replacement combing pad (bolster pads) for my 2520SC, been looking at the foam pads from seadek, and considering either trying to find stock replacements or having an upholstery shop make them for me from scratch. I had an upholstery shop make a set a couple years ago and they totaly...

Well maybe since the hull penetration is in place maybe I ought to wife it to the tuna tower for freak lightning strikes?

Ok thanks for that

Lots of views no responses... Maybe It isn't stock? Do you guys have these on your boats? Mine is a 1992 2520dvsc ? Thanks

My 2520 has a large, I believe stock, anode/ground bar through hull on the rear port side of the bottom of the hull probably 2" wide 8" long, it has to bolt studs on the inside of the boat coming off it with pieces of wire that someone had cut at some time in the past. What is the purpose of...

A trip to the hardware store and a twistlock cord end, a piece or wire, an all weather box with a gfci recepticle and a 1/2" romex connector and you are good to go for about 40bucks in parts, and internet search to figure out how to wire it (as I don't the responsibility of trying to explain it...

10-4, I know for sure that I have a deep v, I was just wondering about placement and making sure the 20 is what I need. I seems like other make boats are steeper at the transom keel... Anyway Ill order the 20 deg. Thanks for the help

that is what I was assuming, it just seems pretty flat right at the keel transom area, thanks for the info.

Looking at upgrading my sonar, to a chirp unit Garmin, with a airmar through hull transducer. I have read a bunch of old threads but havent found a clear answer. Im wondering best place to drill the hole and what degree offset transducer to use, i think 12 and 20 degree are the options. The...

Looking at upgrading my sonar, to a chirp unit Garmin, with a airmar through hull transducer. I have read a bunch of old threads but havent found a clear answer. Im wondering best place to drill the hole and what degree offset transducer to use, i think 12 and 20 degree are the options. The...