Search results

Hello all, I have a 1999 2520 MVSC with the standard 6 rod rocket launcher. As always, I could use a few extra holders up top. But I am trying to avoid replacing the entire unit with a new increased capacity rocket launcher. Has anybody ever added clamp on rod holders to the rocket launcher...

Good day, I am looking for some advice here. I came across a situation yesterday where my 70yr old father ended up overboard with only myself onboard. As you can imagine, this has freaked me out! While I am always aware of my situation, this could have gotten treacherous very quickly. I was...

Removed 2nd freestanding steering station for sale. Pod only, no controls included. Unit has been removed from boat See attached photos for dimensions and condition. Located in South Jersey. Willing to meet for pick-up. Prefer not to ship due to size of pod. $400/OBO

Hello Parker lovers- I am repowering my 2520MVSC with a Suzuki 300HP engine thanks to a blown powerhead on the 21yr old Yammi. I have a 2nd steering station with a wheel and throttle (no electronics or ignition). Over the past 21 years, I can count on 1 hand how many times that I have actually...

Hey guys, I blew a hole in my Yammi 200hp old carbed 2 stroke over the weekend. Looking to repower with a 300 Zuk. Placard on transom says 325hp max rating. But this was 21 yrs ago when the older lighter 2 strokes were around. Should I be worried about the heavier 4 stroke on the notch transom...

I recently installed the 716-SQ-140A-DVSR in place of the standard selector switch this off season. I followed the directions on the site explicitly along with consulting the instructions that came with the unit. This is the single engine, dual batt config. I finally put the boat in the slip...

Hi Folks-I ran into a problem yesterday with my engine that I have never seen before. I am in a new marina with strong currents, so I need to give it some gas when in reverse to get into the slip. When I did this yesterday, the engine kicked out of the water and slammed back down when back in...

Hi Guys- as part of my winter work, I want to replace the fuel fill and vent lines to the tank. The boat is a 1999 2520MVSC and the lines are original. While I am not experiencing any problems, I want to be proactive due to the age of lines. But I have a few questions. 1. What size/diameter are...

Hi guys- Seems that I have developed a problem with my trim/tilt on my Yammie. It is a 1999 S200TXRX.When engine is under load (on plane), the engine seems to drop down from original trimmed position. I am not able to trim it back up while running. Once I pull power back and come off plane, I am...

Good day all- I have a winter project that I need to take care of before spring splash.Last year, I did away with my kicker motor due to lack of use.I now want to remove the bracket, which is a simple matter of 8 bolts.But as these bolts are thru the hull, they would need to be filled for water...

Hi guys, Got a 1999 2520MV with a single Yammi 200 HP with SeaStar hydraulic steering HC 5345 cylinder unit. Have a slight weep from port side of cylinder, so I ordered HS5157 kit to reseal. Instructions seemed pretty simple, but then I got into it. Loosened the gland seal, removed the piston...

Hi guys, My carbed 1999 Y200 is getting long in the tooth and high hours...no real problems but looking to upgrade. I am considering the F250 3.3l vs the F250 4.2l. The main difference that I see is that the 3.3liter F250 dry weight per spec is 608lbs. The 4.2liter F250 dry weight per spec is...

Guys- I value this forum and need some advice here. I have a 2520 with a 1999 Yami 200hp carbed Saltwater Series. It ran great all day yesterday until I went to leave for home. I started the engine and the 3 oil lights were blinking with no horn alarm. Never saw that before! Popped it into gear...

I need some help here guys! I have a 2520MVSC with a single Yam S200TXRX (carbed 6 cyl). Running in yesterday at about 4600rpms (flat day), the overheat alarm went off. Engine came back to about 2000rpms (normal). I turned my head to the engine and saw smoke coming out the exhaust and also water...

I have a 1999 2520MVSC and the 2 white plastic door catches break all the time.If you aren't familiar with what I am talking about. It's the 2 white plastic catches that mount on the inner door and the receptacle is on the frame.There is 1 located uptop and 1 below equidistant from the door...

Guys,I need some advice here. For the past 3 years at the end of the season, the engine loses rpm and fuel consumption rises.In the spring, I take it to the local Mech and he cleans the carbs and all is good again until about mid-Novemeber when it acts up again.The mech charges me about $500...

:?: I am looking for some help here. Had an incident over the weekend where the end of the rode near the chain got damaged.Need to cut rode and resplice to chain. The problem is that it is 8 plait nylon and is for a windlass.There is nobody local to do this splice and I need to do it myself...

Guys, I need some help here. I just finished installing a Lewmar Profish 700 windlass on my 2520MVSC this weekend.Now, I need to replace my current anchor rode and chain with a type compatitible with the windlass and I have a few questions.The mfgr calls for 1/2 in 3 strand medium lay nylon or 8...

Guys, I have a 200HP carbed Yamaha. At the end of last season, it stopped making full power which is about 5300rpm. It only makes 4600-4700 rpm WOT.No cylinders missing, plugs look good also.Engine is also using more fuel than before.Normally at 4000rpm (cruise), I would burn @ 11 gph, but now I...

I have a 1999 200 HP Saltwater Series II carbed OB. Recently, I am only able to make 4700rpms at WOT when before I was at 5300rpm consistently. It then began to lose still more rpms and surge. If I leave the throttle WOT, the engine will wind all the way down and stall. If I retard the throttle...